GymMaster Gym Software Manual

Doors and Readers

GymMaster software combined with door access hardware form an access control system which allows automated individualized entry

Gatekeeper H5

The Gatekeeper H5 is the access control processing unit for the GymMaster access system.

Note: A qualified installer must install the Gatekeeper.

Note: Install it in a safe location where staff can easily get access to the indicator lights, the USB ports and the screen like an access control panel.

How it works

What it does

The Gatekeeper controls the entry and exit of people through the doors of a building. It is integrated with the GymMaster gym management software.

The Gatekeeper connects to these items:

  • Two door readers, one for each door.
  • Two relays, one for each door reader. The relays release the door locks.
  • A maximum of four desktop readers, through the USB ports.
  • Receipt printers and cash drawers (via kicker), through the USB ports.

A member holds an RFID fob near a door reader. The reader sends the fob details to the Gatekeeper. If the member has access, the relay operates with a click, and the door lock releases. The screen shows “open”, the reader beeps, and a pop-up shows in GymMaster.

The LCD screen shows the live status of the Gatekeeper. If the internet connection stops, current members can still check in for short periods (via offline check-in). If the server gets no status for more than 5 minutes, the Visitors page shows the Gatekeeper as offline.

The Gatekeeper must have these three things:

  • A connection to GymMaster.
  • A connection to the Internet, through the RJ45 (LAN) port.
  • A link to a door reader in the GymMaster database.

After you install and test the Gatekeeper, register it at gymmaster.com/registergk.

Parts and connections

All the connectors are on the front plate.

Side Connector Use
Front Relays 1 and 2 (NC, Com, NO) Door lock, one relay for each door
Front Readers 1 and 2 (Sens, Gnd, 12V, A, B) Door reader and push to exit button, one port for each door. Port 1 is the port farthest from the screen.
Front Power (12V) Gatekeeper power supply (12V, 2A). 5.08 mm pitch Phoenix connector.
Front LAN, with Link and Act lights Ethernet cable to the network
Front 4 USB ports Desktop readers, receipt printers and cash drawers
  • Cash drawer: Usually, connect the cash drawer with an RJ11 cable to the receipt printer, not to the Gatekeeper. If you have no applicable receipt printer, use a USB cash drawer kicker. For a cash drawer with only an RS232 connector, use a serial-to-USB adapter, and speak to our team at GymMaster.

Door reader wires (Sentinel reader):

Reader terminal Gatekeeper terminal Wire colour in the guide
Gnd Gnd Black
Pwr (12V) 12V Red
A A White
B B Green

Make sure that the colours agree with the label on the back of the reader. Connect the push to exit button between Sens and Gnd on the same reader port.

Relays:

Each door relay is a Panasonic JW1FSN-DC12V. The Gatekeeper energizes the relay coil when a member has access. Then the relay changes over with a click: Com disconnects from NC and connects to NO.

Item Value
Relay Panasonic JW1FSN-DC12V (high capacity type, sealed)
Contacts 1 Form C (changeover): NC, Com, NO
Coil 12V DC, 44 mA, 530 mW
Contact rating (resistive load) 10A 30V DC
Operate time / release time 15 ms maximum / 5 ms maximum
Mechanical life 5,000,000 operations minimum
Electrical life, NO contact (resistive load) 100,000 operations minimum at 10A 30V DC
Electrical life, NC contact (resistive load) 10,000 operations minimum at 10A 30V DC. 100,000 operations minimum at 5A 30V DC

Caution: Connect only DC door locks of 30V DC maximum to the relay terminals. Do not connect mains (AC) power to the relay terminals. The relay data sheet gives a 250V AC rating, but the Gatekeeper relay ports are for 30V DC maximum.

The ratings are for resistive loads. Door locks are coils, so the relay contacts can wear more quickly. The IN4001 diode at the lock helps to protect the relay contacts. A fail-safe lock uses the NC contact. The NC contact has a shorter life at high current.

These values are from the Panasonic JW relays data sheet (ASCTB190E).

Door lock:

Caution: Do not supply power to door locks from the Gatekeeper. Install the IN4001 diode with the correct polarity. These two things prevent damage to the Gatekeeper.

  • Connect the door lock to the relay with a twin-core cable (70 m maximum).
  • Install an IN4001 diode near the lock.
  • Use a separate power supply for the locks.
  • Use a magnetic lock (12V or 24V DC) or an electric strike (30VDC maximum).
Lock type How the lock operates Relay terminals
Fail safe The lock must have power to lock. It unlocks when the power stops. NC and Com
Fail secure The lock must have power to unlock. It locks when the power stops. NO and Com

Warning: Fail secure wiring can trap members in the building if the power stops and the UPS fails. We recommend fail-safe wiring. Fail-safe wiring can leave the building unlocked if the power stops and there is no UPS.

Connect the emergency exit switch in the lock circuit, as the wiring diagrams in the quick installation guide show.

Network connection:

The Gatekeeper must have a connection to the internet. Connect it to a router or a network switch with an Ethernet cable.

Requirement Value
Connection Wired Ethernet, Cat5 or Cat6 cable
Outgoing ports (open in the firewall) 22 (SSH), 80 (HTTP), 443 (HTTPS)
Outgoing ping ICMP

Note: If a firewall blocks these ports, the Gatekeeper cannot connect to GymMaster. If an IT team manages your network, ask them to allow (whitelist) the Gatekeeper.

To find a firewall problem, switch off the firewalls in the network for a short test. If the Gatekeeper then operates correctly, a firewall blocks it.

Cables:

  • Door readers: 4-core cable, 18-20 AWG (for longer runs) or a Cat5/6
  • Network: Cat5/6 Ethernet cable.
  • USB: 3 m (10 feet) maximum.

Note: Do not use USB hubs or extension cables. Connect only GymMaster devices to the USB ports. Do not charge phones or other devices from them.

Power:

  • Use the power supply that GymMaster supplies (12V, 2A).
  • We recommend an Uninterruptible Power Supply (UPS) or a battery supply for the Gatekeeper, the door readers, the door locks and the router. Then the system continues to operate when the mains power stops.

Lights, sounds and screen

Indicator Meaning
Screen on The Gatekeeper has power and starts. Start-up takes approximately one minute. Status is shown on the screen.
Screen shows ETH: x and Internet: x Shows network status.
Screen shows readers These are the readers that the Gatekeeper found.
Screen shows a QR code and a 5-letter code The Gatekeeper is in Test Mode. It is not registered.
Screen shows “open” The relay corresponding to the note is open.
Relay click The relay is engaged/disengaged, for example after a member scans an RFID fob.
Link light (green/amber) on The Ethernet cable is correctly connected.
Act light (amber) flashes There is network activity.

Specifications

Item Value
Power requirements 12V 2A
Power consumption 12-24W
Communication protocols RS485, RS232
Input/output ports 4x RS232, 2x RS485
Networking 1x RJ45; IPV4, TCP/IP, HTTP, HTTPS, DNS, DDNS, ARP, RSTP, DHCP
Graphic LCD module 68 mm (2.69 in), with backlight
Door reader RFID ports 2
Desktop reader RFID ports 4
Relay ports 2x 30 VDC, built in (one for each door reader). Panasonic JW1FSN-DC12V relays (1 Form C)
Operating temperature 0 °C - 85 °C
Housing dimensions L=147 mm (5.78 in), H=41 mm (1.61 in), W=100 mm (3.94 in)
Configuration methods Factory configured/client configured
Lock requirements 12-30 VDC

Next - Gatekeeper H4